BEIYANG BTP-2200E USB DRIVER DOWNLOAD

When loading the paper, please put the label mount through the peel-off module according to the process as below: Paper type in the driver Continuous paper Black mark paper Actual paper type Continuous strip paper Non-continuous marked paper Non-continuous Perforated paper Non-continuous edge-gap paper Non-continuous label paper Table 2. User can also choose USB interface to replace Parallel interface. Select paper type according to the table as below: REB user manual V If the print just finishes, you should wait for the platen cool down completely; 3 4 Clean away dusts or dirt on the transmission sensor with alcohol tampon should twisted ; Wait for 5 to 10 minutes until alcohol volatilizes completely, then press down ribbon holder and close top cover. Adjust the tear-off position in vertical direction with one dot as a motion unit.

Uploader: Bragar
Date Added: 25 February 2016
File Size: 61.69 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 60333
Price: Free* [*Free Regsitration Required]

Operation method is as below See figure 2.

BTP E Barcode printer,Direct thermal, dpi,Free shipping on | Alibaba Group

Adjust the printout in tbp-2200e direction with 1 dot as a motion unit. Adjust the printout in horizontal direction with 8 dots as a motion unit. In case of such condensation, do not turn on the power until it has completely gone away.

Paper type in the driver Continuous paper Black mark paper Actual paper type Continuous strip paper Non-continuous marked paper Non-continuous Perforated paper Non-continuous edge-gap paper Non-continuous label paper Table 2.

Error LED beyiang Two flashes Reasons THP is lifted up Micro-switch fault Paper roll is end or no paper roll is loaded Paper jam Paper roll surface is dirty or damaged Settlement Beiyagn press down the THP Contact with maintenance people Load paper roll Remove paper jam Please cross over dirty or damaged part Load paper roll again Clean marked paper sensor surface Set paper type in the uxb driver is same with ussb paper type Make communication cable connection firmly Set the communication interface of the print consisting with that of PC Such as: A Transmission sensor 1 2 3 4 Turn off the printer and open top cover; Lift up the print mechanism and press on the latch to open the paper-pressing module; Clean away dusts or dirt on the transmission sensor with alcohol tampon should twisted ; Wait for 5 to 10 minutes until alcohol volatilizes completely, then press down ribbon holder and close top cover.

Read:  INSTALL DELL QUICKSET DRIVER

BTP-2200E Barcode printer,Direct thermal, 203dpi,Free shipping

B Auto Checkout bt-p2200e Before starting the print job, the printer shall compare the parameter set by customers with current parameter of the printer to decide if it shall initiate the btp-22200e with the process as below: Paper Feed mode and non-auto paper feed mode.

If it is the marked paper, please put black mark downwards; The front end of paper roll should be in the middle of the platen as possible as it can. Provides important information and prompts for printer operation.

The printer finds out USB device drive path and installs this driver depending on this guide. Then the print job stops, the host fails to communicate with the printer.

If users need the further data about these products, please feel free to contact our market department or your local distributor. NPort User Manual The steps for cleaning the THP are as below: Figure G shows the tear-off position upwards, which should be btp-220e0 in negative direction; Figure H shows the tear-off position downwards, which should be adjusted in positive direction; 4 Routine maintenance of the printer Follow the steps as below to clean the THP, platen and sensor monthly.

Beiyyang A shows the print position is upward and should be adjusted in negative direction; Figure B shows the print position is downward and should be beiyant in positive direction.

After pressing pause key, the printer shall exit pause status and print; 3 If the checkout fails, the printer shall alarm: When loading the paper, please put the label mount through the peel-off module according to the process as below: If the problem still cannot be removed, please contact with our distributor or manufacturer.

Read:  LEXMARK C540N PRINTER DOWNLOAD DRIVERS

When data gtp-2200e transmitted, the host should not ignore Busy signal, otherwise it could cause the print data lost; Parallel interface signal uses TTL level.

If it is normal the Printer can continue to work, otherwise please bt-p2200e the THP test page is referred to Appendix 1 Print darkness is too high Operation environment temperature is too high, the THP is overheated.

When using it, ensure that up and down time of host beiyanng is less than 0. It shall enter pause status after success. It is the first time to mount and use the printer; The printer is used again after a long idle time; Replace new type of paper roll; First usn to use it after cleaning the sensor; Fails to identify marks in effect during the print; Operation environment of the ush is changed greatly.

The installation method of the driver: User can also choose USB interface to replace Parallel interface. When the printer identifies that Auto checkout is needed, the printer shall feed two or three labels for checkout. Serial interface and Parallel interface are standard interfaces of printer, RS interface is standard Serial interface, Centronics parallel interface accords with IEEE Self-test page sees appendix 1 ; 2 3 The configuration describes the current settings of the printer.

Turn ribbon wheel to tight it up the loaded paper roll and ribbon see figure 2.

The mount of ribbon output shaft is finished. If any part is short or damaged, please contact with our distributor or manufacturer. The print side should be upside.

When paper roll ID is different, the loading method of paper holder into paper room will be different.